Відео

Very helpful, thank you friend. *****.

Thanks man

Very helpful I am going thru this right now I replaced the sending unit and am still having the issue I'm going to check wiring because it will intermittently spike to 4.9v in alfa obd but also when not spiking be at the correct voltage smh

Can you show me how to change cabin filter in jeep commander. Thank you

Horrible spot where they did the filter . I mean with a lift different story but doing it from the ground? No fun or easy and the damn mess. Oil travels along the front frome/cross bar and the steering rack.

Pretty cool that you can set the electronic parking brake to service using just the radio display. There are a lot of vehicles you need to plug a scanner into to access that option.

in case you have never installed a muffler or exhaust tube before . You should refer to this video

What rebuild kit is available and from where? Part#?

Oh yea, living life one quarter turn at a time

Excellent video. Your video helped me replace my own driveshaft in my 15 cherokee. First one for me.

What a useless video

Great video, not looking forward to doing this job, thanks for such a detailed overview.

Just did mine today and the biggest pain was just taking out my fender liners lol

What kind of grease?

Don’t you need to let air between the steel and the insulation so it does not collect moisture?

That white vac line will fit inside of a piece of weed eater fuel hose with a little silicone lube.

Is this a 3 liter Mazda? The engine bay layout looks similar to my Mazda 6 2006 V6. Also you mention the front and back part of the Valve Cover Gasket. Are there 2 separate parts to this car?

You are a very good teacher! Thank you.

Mines making a low freq kinda whining/ grinding noise at low speeds and largely goes away at highway speeds. I need to do this...but at over 500$ for the driveshaft...Jesus! Thats more than a Porsche Cayenne shaft!

What type of noise were you getting? Did you get noise while on the gas pedal and none while not accelerating?

💜💚🇺🇲🌎🌏🌍👽🥊💪🧠

Did you have a wearing out power steering pump at the time because when you started it somewhat sounded like it

Thank you 👌

good vid....its amazing how everyone leaves the full plastic manifold cover on, and somewhat struggles to take the filter out using a socket extension. You're the first one I saw that did it the easy way.

How did you get the new pitman arm I'm having trouble getting it on ?

U ever figure out what was wrong with it

GOD BLESS MY VERY PROUD BEST FRIEND U STILL MISSING THE POINT USER YOU HAVE PRIDE IN THE GODLY PERSON UR CHOOSE I ONLY THINK IN THE UUSA ONLY U SNAP ON MAC MOE CRAFTSMAN FIRST NOOW THAT THERREE MADE COMPLETELY WEITH ONLY USA PARTS AND LABOR AND NEED YOU AND ALL THE POPULATIONIN THIS GREAT COUNTRY UNITED STATES OF AMEERRICA THEE LAND OF THE FRRE AND HOMME OF THE BRAVVE EVERYTHINNG NOW IS MADE ANNY WEERE BUT I AM N TYHE USA CHINA INDIA VIETNAM ETC EEE NOLONNGER HAVE PRIDEE IN OUR PRODUCTS AND LABOR AMERICA SOLD IT SOUL TO THE DEVIL UH AND GODLY SAKE SAFETY 🛟 IS WITH MY VERY SORRY FOR THE DREAM IS WITH GGONE

Teyvek on outside under steel, rockwool on inside. Best option for pole barns

Could you not just drill the stud out

Informative video and glad to see you and your son having that time together! The Thuren set is now $45! But worth every penny!!

Does this work on a twenty eleven jeep grand cherokee I have hot on one side and cold on the other

Pump Jack, Jack stands and car wheels and your still scared to get under there?😂 I'd trust that over ramps because they fail too. If all 3 fail at the same time it was just your time

I have this same noise on my jeep I couldn't pin point it now I know thanks for the video you helped me out!!

You're son what a lot better helper then my dad was when I did this job. All he did was drink a beer and laugh when i cursed at the shocks. LOL

Never removed carpet from a truck. Is it difficult to place it back into place without it looking like it’s torn up

Getting ready to do the girlfriends car. How much do I charge

before you spend all the time doing that did you hold the mileage reset button down and turn on the key until all the gauges on the dash recycle because it seems to be a problem on this Fiat.silantros junk

idk if anybody noticed but u did all this single handedly literally you used one hand for your camera phone recording it all! jesus christ dude i have the same car jeep cherokee 2015 3.2l v6 (latitude). great car to use and enjoy driving but a total pita to maintain and do repairs on especially if this is the 1st car you started doing diy maintenance on. i guess if u can fix a jeep u can fix any other american car easier?

Upvote this. Remove the passenger front tire and the oil filter is right there!

How do you know which spark plug is #1

Can i use ultra penzoil full synthetic

Hi, great video. You have a failing caliper on the drivers side as I had the exact same thing happen to me! I left it so long the caliper seized against the rotor and had smoke billowing out. Another mention is those one time bolts these manufacturers use, sorry but I think that's a bunch of hooey for the most part, and only follow that rule on head gasket replacement etc. I re-use use those caliper support bolts and red loctite them when installing them.

I have almost same problem..except passengers side has no heat whatsoever even on high. Drivers side works as it should once i replace this ssame sensor drive side ..i also replaced passenger side but it didn't fix...so I'm wondering bad sensor..or is there something else i missed? Also for reference 2015 trailhawk 3.2 and dual climate..thanks any help appreciated

I wouldn’t use a pressure washer, that would risk breaking a hose or wire

Thanks for the video!

Great video, you don't actually have to take the entire 13mm bracket off just loosen it, and the intake manifold will come off. His video helped complete this for the first time, big a thumbs-up!

Hey, I'm having an issue where the rear shaft part seems locked up. Could that be an internal problem with the gears of the case and is this fixable? Or should I just replace. At first I thought my entire transmission was locked up but after removing the drive shaft from the PTU I now see that it is only locked up at the cup or whatever that rear part is technically called. All wheels spin freely except this area.

Ok watching these videos an I'm not sure if it's really my fuel pump now,I have a 5.7 Hemi Dodge Ram pickup it started to go work came back noticed the truck wasn't running so I tried to started it nothing it's cranking but don't start

This looks similar to the one on my dad’s 03 expedition 4.6L. It came factory on it I’m just not sure of if it’s the Pi or non Pi

Can’t you just put jack stands along the side of the car instead where they are meant to be instead of using ramps or jacking it down the middle and putting a jack stand in the middle?